Differences between revisions 9 and 34 (spanning 25 versions)

fs.com Switches purchased in 2021

Below is the commands used to configure the switches we purchased in 2021. The switches are installed as follows:

	Rack 1	Rack 2	Liebert	Rack 4	Rack 5
01	R1S1:S58050-48T4Q (241)	R2S1:S5860-20SQ (240)		R4S1:S5800-48T4S (247)	R5S1:S5810-48TS-P (248)
02	R1S2:S58000-48T4S (242)	R2S2:S5800-48T4S (243)
03		R2S3:S5800-48T4S (244)
04		R2S4:S5800-48T4S (245)
04		R2S5:S5800-48T4S (246)

R2S1:S5860-20SQ, 10.10.129.240

R1S2

R2S2

R2S3

R2S4

R2S5

R4S1

R5S1

R1S1

INET1

INET2

Initial Setup Notes for 5800 Series Switches

SSH into the switch with the default user:pass = "admin:admin"

First Change the password, note that we are using local authentication mode, not "aaa" mode. What is aaa mode? That's for authenticating against a radius/TACACS+ server.

Switch# configure terminal
Switch(config)# username  <username> privilege 4 password <password>
Switch(config)# line vty 0 7
Switch(config-line)# login local
Switch(config-line)# exit
Switch(config)# exit

Set the time

Switch# configure terminal
Switch(config)# clock set datetime 11:30:00 10 26 2013
Switch(config)# clock set summer-time dst date 3 13 2022 02:00:00 11 6 2022 02:00:00 120
Switch(config)# exit

Configure Management IP

Switch# configure terminal
Switch(config)# management ip address 10.10.129.X/24
Switch(config)# exit
Switch# show management ip address

Create VLANs

Switch# configure terminal
Switch (config)# vlan database
Switch (config-vlan)# vlan 10 name Server
Switch (config-vlan)# vlan 100 name Office
Switch (config-vlan)# vlan 116 name Labs
Switch (config-vlan)# vlan 119 name Firewalled
Switch (config-vlan)# exit
Switch (config)# end
Switch#

Setup Management VLAN Interface

Setup management on a vlan interface

switch# configure terminal
switch(config)# interface vlan 10
switch(config)# ip address 10.10.129.X/24
switch(config)# Ctrl+z
Switch# show management ip address

Set the banner to show the name of the switch

Switch# configure terminalThe // at the end of the line indicates the start of a comment:
Switch# banner login # You are logged into RXSY #
Switch# exit
Switch# show running //validates that it worked

In the web interface

Configuration
- Ethernet Status (Change eth-0-50 to trunk)
- VLAN (Set VLANs for 10,100,116,119 as appropriate - default is 116; Make sure to change eth-0-50 default 10 allow 10,100,116,119)
Maintenance
- System Configuration (file out page and save)
- User Management (Add scot and vadmin; change password for admin)
- Reboot/Save (save the configuration)
Network
- IP Routing
  - IPv4 Static Route Information
    - New:
    - Destination = 0.0.0.0
    - Mask = 0.0.0.0
    - Nexthop = 10.10.129.1
    - Distance = 1

Common Commands

The // at the end of the line indicates the start of a comment:

===Show Port Status===

Switch# show interface status //show status of all the ports
Switch# show interface eth-0-49 //shows the status of eth-0-49

===Show VLAN information for port===

switch# show interface switchport interface eth-0-1

Backup and Restore the switch Configuration

To backup the configuration, ssh into the switch and perform the following:

Switch# copy flash:/startup-config.conf mgmt-if scp://10.10.129.X/startup-config.conf

To download a configuration file:

Switch# copy mgmt-if scp://10.10.10.163/startup-config.conf flash:/startup-config.conf

LACP configuration on S5850 10 GIG Switch

Switch# configure terminal
Switch(config)# port-channel 1 load-balance-mode dynamic
Switch(config)# interface eth-0-47
Switch(config-if)# no shutdown
Switch(config-if)# channel-group 1 mode active //active is the key word to get you LACP!
Switch(config-if)# edit
Switch(config)# [repeat previous 4 for each port]
Switch(config)# end
Switch# show channel-group summary

NetworkConfiguration/FsComSwitchConfiguration (last edited 2022-02-16 23:32:03 by scot)

-  ⇤ ← Revision 9 as of 2022-01-05 21:49:22 → 
  Size: 1815
  Editor: scot
  Comment:
+   ← Revision 34 as of 2022-01-19 20:47:54 → ⇥
  Size: 4536
  Editor: scot
  Comment:
-Deletions are marked like this.
+Additions are marked like this.
 Line 3:
-Below is the commands used to configure the switches we purchased in 2021
+Below is the commands used to configure the switches we purchased in 2021. The switches are installed as follows:

||    || '''Rack 1'''              || '''Rack 2'''            || '''Liebert''' ||'''Rack 4'''       ||'''Rack 5'''        ||
|| 01 || !R1S1:S58050-48T4Q (241)  || !R2S1:S5860-20SQ (240)  ||               || !R4S1:S5800-48T4S (247)|| !R5S1:S5810-48TS-P (248)||
|| 02 || !R1S2:S58000-48T4S (242)  || !R2S2:S5800-48T4S (243) ||               || || ||
|| 03 ||                           || !R2S3:S5800-48T4S (244) ||               || || ||
|| 04 ||                           || !R2S4:S5800-48T4S (245) ||               || || ||
|| 04 ||                           || !R2S5:S5800-48T4S (246) ||               || || ||

||<-13>!R2S1:S5860-20SQ, 10.10.129.240 ||
||!R1S2||!R2S2||!R2S3||!R2S4 ||!R2S5 ||!R4S1 ||!R5S1 || || || || || ||!R1S1||
||INET1||INET2|| || || || || || || || || || || ||
-Line 10:
+Line 22:
-Line 13:
+Line 24:
+Switch(config)# username  <username> privilege 4 password <password>
-Line 14:
+Line 26:
-Switch(config-line)# login
Switch(config-line)# line-password abc
+Switch(config-line)# login local
Switch(config-line)# exit
-Line 17:
+Line 29:
 }}}
-Line 28:
+Line 40:
+'''Configure Management IP'''
{{{
Switch# configure terminal
Switch(config)# management ip address 10.10.129.X/24
Switch(config)# exit
Switch# show management ip address
}}}
-Line 29:
+Line 49:
+{{{
Switch# configure terminal
Switch (config)# vlan database
Switch (config-vlan)# vlan 10 name Server
Switch (config-vlan)# vlan 100 name Office
Switch (config-vlan)# vlan 116 name Labs
Switch (config-vlan)# vlan 119 name Firewalled
Switch (config-vlan)# exit
Switch (config)# end
Switch# 
}}}
-Line 30:
+Line 61:
-'''Setup Management Interface'''
+'''Setup Management VLAN Interface'''
-Line 42:
+Line 72:
+'''Set the banner to show the name of the switch'''
{{{
Switch# configure terminalThe // at the end of the line indicates the start of a comment:
Switch# banner login # You are logged into RXSY #
Switch# exit
Switch# show running //validates that it worked
}}}
-Line 43:
+Line 80:
+'''In the web interface'''

 * Configuration 
   * Ethernet Status (Change eth-0-50 to trunk)
   * VLAN (Set VLANs for 10,100,116,119 as appropriate - default is 116; Make sure to change eth-0-50 default 10 allow 10,100,116,119)

 * Maintenance
   * System Configuration (file out page and save)
   * User Management (Add scot and vadmin; change password for admin)
   * Reboot/Save (save the configuration)

 * Network 
   * IP Routing
     * IPv4 Static Route Information
       * New:
       * Destination = 0.0.0.0
       * Mask = 0.0.0.0
       * Nexthop = 10.10.129.1
       * Distance = 1
-Line 48:
+Line 104:
-'''Show Port Status'''
+===Show Port Status===
-Line 56:
+Line 112:
-'''Show VLAN information for port'''
+===Show VLAN information for port===
-Line 61:
+Line 117:
-== Backup and Restore the switch Configuration ==
+=== Backup and Restore the switch Configuration ===
-Line 74:
+Line 130:
+=== LACP configuration on S5850 10 GIG Switch ===

{{{
Switch# configure terminal
Switch(config)# port-channel 1 load-balance-mode dynamic
Switch(config)# interface eth-0-47
Switch(config-if)# no shutdown
Switch(config-if)# channel-group 1 mode active //active is the key word to get you LACP!
Switch(config-if)# edit
Switch(config)# [repeat previous 4 for each port]
Switch(config)# end
Switch# show channel-group summary
}}}

Diff for "NetworkConfiguration/FsComSwitchConfiguration"

fs.com Switches purchased in 2021

Initial Setup Notes for 5800 Series Switches

Common Commands

Backup and Restore the switch Configuration

LACP configuration on S5850 10 GIG Switch