Differences between revisions 12 and 30 (spanning 18 versions)

fs.com Switches purchased in 2021

Below is the commands used to configure the switches we purchased in 2021. The switches are installed as follows:

	Rack 1	Rack 2	Liebert	Rack 4	Rack 5
01	R1S1:S58050-48T4Q (241)	R2S1:S5860-20SQ (240)		R4S1:S5800-48T4S (247)	R5S1:S5810-48TS-P (248)
02	R1S2:S58000-48T4S (242)	R2S2:S5800-48T4S (243)
03		R2S3:S5800-48T4S (244)
04		R2S4:S5800-48T4S (245)
04		R2S5:S5800-48T4S (246)

R2S1:S5860-20SQ, 10.10.129.240

R1S2

R2S2

R2S3

R2S4

R2S5

R4S1

R5S1

R1S1

INET1

INET2

Initial Setup Notes for 5800 Series Switches

SSH into the switch with the default user:pass = "admin:admin"

First Change the password, note that we are using local authentication mode, not "aaa" mode. What is aaa mode? That's for authenticating against a radius/TACACS+ server.

Switch# configure terminal
Switch(config)# username  <username> privilege 4 password <password>
Switch(config)# line vty 0 7
Switch(config-line)# login local
Switch(config-line)# exit
Switch(config)# exit

Set the time

Switch# configure terminal
Switch(config)# clock set datetime 11:30:00 10 26 2013
Switch(config)# clock set summer-time dst date 3 13 2022 02:00:00 11 6 2022 02:00:00 120
Switch(config)# exit

Configure Management IP

Switch# configure terminal
Switch(config)# management ip address 10.10.129.X/24
Switch(config)# exit
Switch# show management ip address

Create VLANs

Switch# configure terminal
Switch (config)# vlan database
Switch (config-vlan)# vlan 10 name Server
Switch (config-vlan)# vlan 100 name Office
Switch (config-vlan)# vlan 116 name Labs
Switch (config-vlan)# vlan 119 name Firewalled
Switch (config-vlan)# exit
Switch (config)# end
Switch#

Setup Management VLAN Interface

Setup management on a vlan interface

switch# configure terminal
switch(config)# interface vlan 10
switch(config)# ip address 10.10.129.X/24
switch(config)# Ctrl+z
Switch# show management ip address

Set the banner to show the name of the switch

Switch# configure terminalThe // at the end of the line indicates the start of a comment:
Switch# banner login # You are logged into RXSY #
Switch# exit
Switch# show running //validates that it worked

In the web interface

Configuration
- Ethernet Status (Change eth-0-50 to trunk)
- VLAN (Set VLANs for 10,100,116,119 as appropriate - default is 116; Make sure to change eth-0-50 default 10 allow 10,100,116,119)
Maintenance
- System Configuration (file out page and save)
- User Management (Add scot and vadmin; change password for admin)
- Reboot/Save (save the configuration)

Common Commands

The // at the end of the line indicates the start of a comment:

Show Port Status

Switch# show interface status //show status of all the ports
Switch# show interface eth-0-49 //shows the status of eth-0-49

Show VLAN information for port

switch# show interface switchport interface eth-0-1

Backup and Restore the switch Configuration

To backup the configuration, ssh into the switch and perform the following:

Switch# copy flash:/startup-config.conf mgmt-if scp://10.10.129.X/startup-config.conf

To download a configuration file:

Switch# copy mgmt-if scp://10.10.10.163/startup-config.conf flash:/startup-config.conf

NetworkConfiguration/FsComSwitchConfiguration (last edited 2022-02-16 23:32:03 by scot)

-  ⇤ ← Revision 12 as of 2022-01-06 16:57:29 → 
  Size: 2835
  Editor: scot
  Comment:
+   ← Revision 30 as of 2022-01-09 21:53:31 → ⇥
  Size: 3895
  Editor: scot
  Comment:
-Deletions are marked like this.
+Additions are marked like this.
 Line 5:
-||    || '''Rack 1'''      || '''Rack 2'''      || '''Liebert''' ||'''Rack 4'''      ||'''Rack 5'''       ||
|| 01 || R1S1:S58050-48T4Q  || R2S1:S5860-20SQ  ||               || R4S1:S5800-48T4S || R5S1:S5810-48TS-P ||
|| 02 || R1S2:S58000-48T4S  || R2S2:S5800-48T4S ||               || || ||
|| 02 || R1S2:S58000-48T4S  || R2S3:S5800-48T4S ||               || || ||
|| 02 || R1S2:S58000-48T4S  || R2S4:S5800-48T4S ||               || || ||
|| 02 || R1S2:S58000-48T4S  || R2S5:S5800-48T4S ||               || || ||
+||    || '''Rack 1'''              || '''Rack 2'''            || '''Liebert''' ||'''Rack 4'''       ||'''Rack 5'''        ||
|| 01 || !R1S1:S58050-48T4Q (241)  || !R2S1:S5860-20SQ (240)  ||               || !R4S1:S5800-48T4S (247)|| !R5S1:S5810-48TS-P (248)||
|| 02 || !R1S2:S58000-48T4S (242)  || !R2S2:S5800-48T4S (243) ||               || || ||
|| 03 ||                           || !R2S3:S5800-48T4S (244) ||               || || ||
|| 04 ||                           || !R2S4:S5800-48T4S (245) ||               || || ||
|| 04 ||                           || !R2S5:S5800-48T4S (246) ||               || || ||

||<-13>!R2S1:S5860-20SQ, 10.10.129.240 ||
||!R1S2||!R2S2||!R2S3||!R2S4 ||!R2S5 ||!R4S1 ||!R5S1 || || || || || ||!R1S1||
||INET1||INET2|| || || || || || || || || || || ||
-Line 17:
+Line 22:
-Line 20:
+Line 24:
+Switch(config)# username  <username> privilege 4 password <password>
-Line 21:
+Line 26:
-Switch(config-line)# login
Switch(config-line)# line-password abc
+Switch(config-line)# login local
Switch(config-line)# exit
-Line 24:
+Line 29:
 }}}
-Line 35:
+Line 40:
-'''Set the banner to show the name of the switch'''
+'''Configure Management IP'''
-Line 37:
+Line 42:
-Switch# configure terminalThe // at the end of the line indicates the start of a comment:
Switch# banner login # You are logged into RXSY #
Switch# exit
Switch# show running //validates that it worked
+Switch# configure terminal
Switch(config)# management ip address 10.10.129.X/24
Switch(config)# exit
Switch# show management ip address
-Line 42:
+Line 47:
-{{{
Switch# show interface status //show status of all the ports
Switch# show interface eth-0-49 //shows the status of eth-0-49
}}}
-Line 52:
+Line 51:
+Switch (config)# vlan database
Switch (config-vlan)# vlan 10 name Server
Switch (config-vlan)# vlan 100 name Office
Switch (config-vlan)# vlan 116 name Labs
Switch (config-vlan)# vlan 119 name Firewalled
Switch (config-vlan)# exit
Switch (config)# end
-Line 55:
+Line 61:
-'''Setup Management Interface'''
+'''Setup Management VLAN Interface'''
-Line 67:
+Line 72:
+'''Set the banner to show the name of the switch'''
{{{
Switch# configure terminalThe // at the end of the line indicates the start of a comment:
Switch# banner login # You are logged into RXSY #
Switch# exit
Switch# show running //validates that it worked
}}}
-Line 68:
+Line 80:
+'''In the web interface'''

 * Configuration 
   * Ethernet Status (Change eth-0-50 to trunk)
   * VLAN (Set VLANs for 10,100,116,119 as appropriate - default is 116; Make sure to change eth-0-50 default 10 allow 10,100,116,119)

 * Maintenance
   * System Configuration (file out page and save)
   * User Management (Add scot and vadmin; change password for admin)
   * Reboot/Save (save the configuration)

Diff for "NetworkConfiguration/FsComSwitchConfiguration"

fs.com Switches purchased in 2021

Initial Setup Notes for 5800 Series Switches

Common Commands

Backup and Restore the switch Configuration