|
Size: 2273
Comment:
|
Size: 2835
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 3: | Line 3: |
| Below is the commands used to configure the switches we purchased in 2021 | Below is the commands used to configure the switches we purchased in 2021. The switches are installed as follows: || || '''Rack 1''' || '''Rack 2''' || '''Liebert''' ||'''Rack 4''' ||'''Rack 5''' || || 01 || R1S1:S58050-48T4Q || R2S1:S5860-20SQ || || R4S1:S5800-48T4S || R5S1:S5810-48TS-P || || 02 || R1S2:S58000-48T4S || R2S2:S5800-48T4S || || || || || 02 || R1S2:S58000-48T4S || R2S3:S5800-48T4S || || || || || 02 || R1S2:S58000-48T4S || R2S4:S5800-48T4S || || || || || 02 || R1S2:S58000-48T4S || R2S5:S5800-48T4S || || || || |
fs.com Switches purchased in 2021
Below is the commands used to configure the switches we purchased in 2021. The switches are installed as follows:
|
Rack 1 |
Rack 2 |
Liebert |
Rack 4 |
Rack 5 |
01 |
R1S1:S58050-48T4Q |
R2S1:S5860-20SQ |
|
R4S1:S5800-48T4S |
R5S1:S5810-48TS-P |
02 |
R1S2:S58000-48T4S |
R2S2:S5800-48T4S |
|
|
|
02 |
R1S2:S58000-48T4S |
R2S3:S5800-48T4S |
|
|
|
02 |
R1S2:S58000-48T4S |
R2S4:S5800-48T4S |
|
|
|
02 |
R1S2:S58000-48T4S |
R2S5:S5800-48T4S |
|
|
|
Initial Setup Notes for 5800 Series Switches
SSH into the switch with the default user:pass = "admin:admin"
First Change the password, note that we are using local authentication mode, not "aaa" mode. What is aaa mode? That's for authenticating against a radius/TACACS+ server.
Switch# configure terminal Switch(config)# line vty 0 7 Switch(config-line)# login Switch(config-line)# line-password abc Switch(config)# exit
Set the time
Switch# configure terminal Switch(config)# clock set datetime 11:30:00 10 26 2013 Switch(config)# clock set summer-time dst date 3 13 2022 02:00:00 11 6 2022 02:00:00 120 Switch(config)# exit
Set the banner to show the name of the switch
Switch# configure terminalThe // at the end of the line indicates the start of a comment: Switch# banner login # You are logged into RXSY # Switch# exit Switch# show running //validates that it worked
Switch# show interface status //show status of all the ports Switch# show interface eth-0-49 //shows the status of eth-0-49
Create VLANs
Switch# configure terminal Switch#
Setup Management Interface
Setup management on a vlan interface
switch# configure terminal switch(config)# interface vlan 10 switch(config)# ip address 10.10.129.X/24 switch(config)# Ctrl+z Switch# show management ip address
Common Commands
The // at the end of the line indicates the start of a comment:
Show Port Status
Switch# show interface status //show status of all the ports Switch# show interface eth-0-49 //shows the status of eth-0-49
Show VLAN information for port
switch# show interface switchport interface eth-0-1
Backup and Restore the switch Configuration
To backup the configuration, ssh into the switch and perform the following:
Switch# copy flash:/startup-config.conf mgmt-if scp://10.10.129.X/startup-config.conf
To download a configuration file:
Switch# copy mgmt-if scp://10.10.10.163/startup-config.conf flash:/startup-config.conf