473
Comment:
|
2927
|
Deletions are marked like this. | Additions are marked like this. |
Line 3: | Line 3: |
== Initial Setup Notes == | Below is the commands used to configure the switches we purchased in 2021. The switches are installed as follows: || || '''Rack 1''' || '''Rack 2''' || '''Liebert''' ||'''Rack 4''' ||'''Rack 5''' || || 01 || !R1S1:S58050-48T4Q || !R2S1:S5860-20SQ || || !R4S1:S5800-48T4S || !R5S1:S5810-48TS-P || || 02 || !R1S2:S58000-48T4S || !R2S2:S5800-48T4S || || || || || 03 || || !R2S3:S5800-48T4S || || || || || 04 || || !R2S4:S5800-48T4S || || || || ||<-13>!R1S1:S5860-20SQ, 10.10.129.240 || ||!R1S2|| || || || || || || || || || || ||!R1S1|| ||INET1||INET2|| || || || || || || || || || || || == Initial Setup Notes for 5800 Series Switches == |
Line 16: | Line 29: |
'''Set the time''' {{{ Switch# configure terminal Switch(config)# clock set datetime 11:30:00 10 26 2013 Switch(config)# clock set summer-time dst date 3 13 2022 02:00:00 11 6 2022 02:00:00 120 Switch(config)# exit }}} '''Set the banner to show the name of the switch''' {{{ Switch# configure terminalThe // at the end of the line indicates the start of a comment: Switch# banner login # You are logged into RXSY # Switch# exit Switch# show running //validates that it worked }}} {{{ Switch# show interface status //show status of all the ports Switch# show interface eth-0-49 //shows the status of eth-0-49 }}} '''Create VLANs''' {{{ Switch# configure terminal Switch# }}} '''Setup Management Interface''' Setup management on a vlan interface {{{ switch# configure terminal switch(config)# interface vlan 10 switch(config)# ip address 10.10.129.X/24 switch(config)# Ctrl+z Switch# show management ip address }}} == Common Commands == The // at the end of the line indicates the start of a comment: '''Show Port Status''' {{{ Switch# show interface status //show status of all the ports Switch# show interface eth-0-49 //shows the status of eth-0-49 }}} '''Show VLAN information for port''' {{{ switch# show interface switchport interface eth-0-1 }}} == Backup and Restore the switch Configuration == To backup the configuration, ssh into the switch and perform the following: {{{ Switch# copy flash:/startup-config.conf mgmt-if scp://10.10.129.X/startup-config.conf }}} To download a configuration file: {{{ Switch# copy mgmt-if scp://10.10.10.163/startup-config.conf flash:/startup-config.conf }}} |
fs.com Switches purchased in 2021
Below is the commands used to configure the switches we purchased in 2021. The switches are installed as follows:
|
Rack 1 |
Rack 2 |
Liebert |
Rack 4 |
Rack 5 |
01 |
R1S1:S58050-48T4Q |
R2S1:S5860-20SQ |
|
R4S1:S5800-48T4S |
R5S1:S5810-48TS-P |
02 |
R1S2:S58000-48T4S |
R2S2:S5800-48T4S |
|
|
|
03 |
|
R2S3:S5800-48T4S |
|
|
|
04 |
|
R2S4:S5800-48T4S |
|
|
|
R1S1:S5860-20SQ, 10.10.129.240 |
||||||||||||
R1S2 |
|
|
|
|
|
|
|
|
|
|
|
R1S1 |
INET1 |
INET2 |
|
|
|
|
|
|
|
|
|
|
|
Initial Setup Notes for 5800 Series Switches
SSH into the switch with the default user:pass = "admin:admin"
First Change the password, note that we are using local authentication mode, not "aaa" mode. What is aaa mode? That's for authenticating against a radius/TACACS+ server.
Switch# configure terminal Switch(config)# line vty 0 7 Switch(config-line)# login Switch(config-line)# line-password abc Switch(config)# exit
Set the time
Switch# configure terminal Switch(config)# clock set datetime 11:30:00 10 26 2013 Switch(config)# clock set summer-time dst date 3 13 2022 02:00:00 11 6 2022 02:00:00 120 Switch(config)# exit
Set the banner to show the name of the switch
Switch# configure terminalThe // at the end of the line indicates the start of a comment: Switch# banner login # You are logged into RXSY # Switch# exit Switch# show running //validates that it worked
Switch# show interface status //show status of all the ports Switch# show interface eth-0-49 //shows the status of eth-0-49
Create VLANs
Switch# configure terminal Switch#
Setup Management Interface
Setup management on a vlan interface
switch# configure terminal switch(config)# interface vlan 10 switch(config)# ip address 10.10.129.X/24 switch(config)# Ctrl+z Switch# show management ip address
Common Commands
The // at the end of the line indicates the start of a comment:
Show Port Status
Switch# show interface status //show status of all the ports Switch# show interface eth-0-49 //shows the status of eth-0-49
Show VLAN information for port
switch# show interface switchport interface eth-0-1
Backup and Restore the switch Configuration
To backup the configuration, ssh into the switch and perform the following:
Switch# copy flash:/startup-config.conf mgmt-if scp://10.10.129.X/startup-config.conf
To download a configuration file:
Switch# copy mgmt-if scp://10.10.10.163/startup-config.conf flash:/startup-config.conf